Delivery is an extra cost unless stated on the quotation.
Liaison with local authorities for approvals may be done using our Plan Assist program for an additional charge.
Construction and erection of your kit may be offered, as an extra cost, depending on your location in Australia.
Our computerised design and quoting systems ensure we include all that you need for your project.

Yes - Most of our clients erect their own sheds with the help of the construction guide we supply on order.
Remember if you run into trouble our Customer Service Division is there for assistance. Our Customer Service Division has the additional support of our engineering and building consultants.
Alternatively We can supply you a list of contractors that you can deal with direct and they can price the construction for you
or
as registered builders SambecSheds can quote for full construction including slab.

We can dispatch our product from 23 locations around Australia. Delivery charges apply dependant on the site location. Some remote area are better serviced by your local courier and we will advise you if that is necessary

In most cases you will. We provide you with Engineering details of your building with 10% deposit. Your job is then reserved until you notify us, in writing, that its been approved and a further 40% deposit is payed. We have never had to refund a deposit as we work with you and your council but if it is not approved your deposit is refunded on notification of refusal from the council. SambecSheds, unlike most other shed kit companies, can offer you Plan Assist - which will speed up the planning approval

When you choose a shed made from BHP BlueScope Steel you know its been designed for a long low maintenance life because unlike cheap imported steel it can withstand Australia's harsh conditions. There are other imported steel products out there that look the same but don't necessarily perform the same. Always ask for BHP BlueScope steel by name

All our buildings are supplied in accordance with The Building Code of Australia and in accordanace with AS/NZS 1170.2. Most buildings conform to Region A now N2 specification which covers 90% of Australia. Please remember that you must check with your local council for the exact rating needed for where you will be erecting the new shed. To check wind rating for your area click here.

Your Shed. Your Choice is our motto. We will give you all the assistance we can to provide you with exactly what you want.

All materials are covered with the manufactures warranty, which is a minimum of 15 years. These warranties can be viewed here  

Yes and its easy to apply and be approved.You dont have to visit the bank 2 to 3 times and make appointments with bank managers. Keep in mind that all the bank staff does is complete an application form, without truly understanding the important issues in a successful application. Faster - By using our direct access to the banking system, the Web, phone and fax we are able to greatly reduce the time it takes to get a loan. Greater Success - By understanding the information you should provide will greatly enhance your chances of succeeding with your application.

Yes, the proprietors of SambecSheds are registered builders with the Master Builders Association

Yes, we offer complete design, engineering, fabrication and construction of our full range. We also offer our unique  Plan Assist Scheme - which will speed up planning approvals if they are need for your building.

A portal frame is a technical term that distinguishes between an old style "Truss" frame with a horizontal bottom cord and zigzag angle iron, and a frame that follows the roofline. A portal frame provides for a neater appearance and gives greater internal height clearance.

A Skiilion roof is a roof that does not have a peak inn it and is sometimes called a flat roof. This is not necessarily correct because to allow rainwater to flow into a gutter some fall on the roof is required.. The fall will be dependent upon the roof cladding manufacturer requirements. For example, Stramit "Monoclad" roof sheet requires a minimum 2 degree fall while a Stramit "Corrugated" roof sheet requires a minimum 5 degree fall on the roof.

At SambecSheds, we do not "roll" our own material, thereby keeping the highest possible quality control standards. We source all our materials from major suppliers such as BHP, Stramit Industries and B&D Roll-A-Doors to name a few. Because we use only recognised suppliers, we maintain 100% quality control over the products that come into our warehouse. In the unlikely event that the material is defective in any way it is promptly returned to the supplier and replaced to our satisfaction.

All SambecSheds buildings come standard with Zincalume Roof Cladding, Zincalume Wall Cladding (where required), guttering, down pipes and Fibreglass (Roof Sheet) Skylights.

Roll-A-Doors, Sliding Doors, Personal Access Doors, and Industrial Exit Doors are all available. Because we have flexibility in our designs, a mixture of doors can be incorporated into your shed design. Other options include Colorbond finish, Foil Insulation / 50mm Blanket Foil and Wire Mesh under roof, roof ventilation, Polycarbonate Skylights, Aluminium Sliding Windows, Glass Sliding Doors, Wall Vents, Octagonal Vents, remote control Roll-A-Door, and Removable Roll Door Mullion (if required). We supply windows and Glass Sliding Doors - many other large shed kit companies on make an opening in the building and you have to source the widows yourself. What alternative options do you offer? You can add a raised section to the Farm Shed / Garage to give it an "American Barn" look. The roof pitch on the side sections are 10 degrees, then a 600mm "step-up" with a 20 degree pitch in the centre section. Other popular options include an open sided "Machinery Shed", with one bay completely enclosed and the other bay(s) open on one side, or a "Garaport", with the front section of the building a carport (roof with no walls) and the rear section an enclosed shed. With all our structures there is the capability of having a "lean-to" attached to the side of the building, either as a roof only or fully enclosed. Unlike other companies that stay strictly within "standard" designs, we are happy to consider unusual and odd shape requests that you may have.

Whilst we have standard sizes from which to quote on which offers sheds at wholesale pricing, we are happy to quote on any customer request since our modern computerised systems allow for just that. Do you sell buildings in "self erect kit" form? We can supply our sheds in kit form for you to erect yourself. Detailed instructions and footing plans are provided to assist you. We are only ever a telephone call away if you need any clarification and we are always willing to assist where required.

For your peace of mind we provide the full manufacturers warranty on all supplied components.

Our portal frame design Shed originated from our very heavy duty Farm Shed range. While many other Garages can sometimes be classified as oversize Garden Sheds in design, the SambecSheds Garage has the inherent strength afforded much larger structures. We do not scrimp on material thickness. There are many portal frame design buildings on the market. Please don't be misguided by cheap prices. You get what you pay for. We actively encourage customers to inspect our buildings and compare them to our competitors. Finally, because we are actually in the business of both supplying and erecting our own buildings, we care about the quality and workmanship of the end result.